TOUCH(1) General Commands Manual TOUCH(1)

touch — change file access and modification times

touch [-acm] [-r ref_file|-t time|-d date_time] file...

The touch utility shall change the last data modification timestamps, the last data access timestamps, or both.

The time used can be specified by the -t time option-argument, the corresponding time fields of the file referenced by the -r ref_file option-argument, or the -d date_time option-argument, as specified in the following sections. If none of these are specified, touch shall use the current time.

For each file operand, touch shall perform actions equivalent to the following functions defined in the System Interfaces volume of POSIX.1-2008:

  1. If file does not exist:
    1. The creat(3) function is called with the following arguments:
      • The file operand is used as the path argument.
      • The value of the bitwise-inclusive OR of S_IRUSR, S_IWUSR, S_IRGRP, S_IWGRP, S_IROTH, and S_IWOTH is used as the argument.
    2. The futimens(3) function is called with the following arguments:
      • The file descriptor opened in step 1a.
      • The access time and the modification time, set as described in the OPTIONS section, are used as the first and second elements of the times array argument, respectively.
  2. If file exists, the utimensat(3) function is called with the following arguments:
    1. The AT_FDCWD special value is used as the argument.
    2. The file operand is used as the path argument.
    3. The access time and the modification time, set as described in the OPTIONS section, are used as the first and second elements of the times array argument, respectively.
    4. The argument is set to zero.

The touch utility shall conform to XBD V1_chap12(7).

The following options shall be supported:

Change the access time of file . Do not change the modification time unless -m is also specified.
Do not create a specified file if it does not exist. Do not write any diagnostic messages concerning this condition.
Use the specified date_time instead of the current time. The option-argument shall be a string of the form: 
YYYY-MM-DDThh:mm:SS[.frac][tz]

or:

YYYY-MM-DDThh:mm:SS[,frac][tz]

where:

  • are at least four decimal digits giving the year.
  • , DD, hh, mm, and SS are as with -t time.
  • is the time designator, and can be replaced by a single <space>.
  • frac ] and [, frac ] are either empty, or a <period> ( ‘’. ) or a <comma> ( ‘’, ) respectively, followed by one or more decimal digits, specifying a fractional second.
  • [ tz ] is either empty, signifying local time, or the letter ‘Z’, signifying UTC. If [ tz ] is empty, the resulting time shall be affected by the value of the TZ environment variable.

If the resulting time precedes the Epoch, the behavior is implementation-defined. If the time cannot be represented as the file's timestamp, touch shall exit immediately with an error status.

Change the modification time of file . Do not change the access time unless -a is also specified.
Use the corresponding time of the file named by the pathname ref_file instead of the current time.
Use the specified time instead of the current time. The option-argument shall be a decimal number of the form: 
[[CC]YY]MMDDhhmm[.SS]

where each two digits represents the following:

The month of the year [01,12].
The day of the month [01,31].
The hour of the day [00,23].
The minute of the hour [00,59].
The first two digits of the year (the century).
The second two digits of the year.
The second of the minute [00,60].

Both CC and YY shall be optional. If neither is given, the current year shall be assumed. If YY is specified, but CC is not, CC shall be derived as follows:

If YY is: CC becomes:
[69,99] 19
[00,68] 20
It is expected that in a future version of this standard the default century inferred from a 2-digit year will change. (This would apply to all commands accepting a 2-digit year as input.)

The resulting time shall be affected by the value of the TZ environment variable. If the resulting time value precedes the Epoch, the behavior is implementation-defined. If the time is out of range for the file's timestamp, touch shall exit immediately with an error status. The range of valid times past the Epoch is implementation-defined, but it shall extend to at least the time 0 hours, 0 minutes, 0 seconds, January 1, 2038, Coordinated Universal Time. Some implementations may not be able to represent dates beyond January 18, 2038, because they use signed int as a time holder.

The range for SS is [00,60] rather than [00,59] because of leap seconds. If SS is 60, and the resulting time, as affected by the TZ environment variable, does not refer to a leap second, the resulting time shall be one second after a time where SS is 59. If SS is not given a value, it is assumed to be zero.

If neither the -a nor -m options were specified, touch shall behave as if both the -a and -m options were specified.

The following operands shall be supported:

file
A pathname of a file whose times shall be modified.

Not used.

None.

The following environment variables shall affect the execution of touch:

Provide a default value for the internationalization variables that are unset or null. (See XBD for the precedence of internationalization variables used to determine the values of locale categories.)
If set to a non-empty string value, override the values of all the other internationalization variables.
Determine the locale for the interpretation of sequences of bytes of text data as characters (for example, single-byte as opposed to multi-byte characters in arguments).
Determine the locale that should be used to affect the format and contents of diagnostic messages written to standard error.
[ XSI] Determine the location of message catalogs for the processing of LC_MESSAGES.
Determine the timezone to be used for interpreting the time option-argument. If TZ is unset or null, an unspecified default timezone shall be used.

Default.

Not used.

The standard error shall be used only for diagnostic messages.

None.

None.

The following exit values shall be returned:

The utility executed successfully and all requested changes were made.
An error occurred.

Default.

The interpretation of time is taken to be seconds since the Epoch (see XBD V1_chap04(7)). It should be noted that implementations conforming to the System Interfaces volume of POSIX.1-2008 do not take leap seconds into account when computing seconds since the Epoch. When SS =60 is used, the resulting time always refers to 1 plus seconds since the Epoch for a time when SS =59.

Although the -t time option-argument specifies values in 1969, the access time and modification time fields are defined in terms of seconds since the Epoch (00:00:00 on 1 January 1970 UTC). Therefore, depending on the value of TZ when touch is run, there is never more than a few valid hours in 1969 and there need not be any valid times in 1969.

One ambiguous situation occurs if -t time is not specified, -r ref_file is not specified, and the first operand is an eight or ten-digit decimal number. A portable script can avoid this problem by using:

touch -- file

or:

touch ./file

in this case.

If the T time designator is replaced by a <space> for the -d date_time option-argument, the <space> must be quoted to prevent the shell from splitting the argument.

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 local time:

touch -d 2007-11-12T10:15:30 dwc

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 UTC:

touch -d 2007-11-12T10:15:30Z nick

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 local time with a fractional second timestamp of .002 seconds:

touch -d 2007-11-12T10:15:30,002 gwc

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 UTC with a fractional second timestamp of .002 seconds:

touch -d "2007-11-12 10:15:30.002Z" ajosey

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:00 local time:

touch -t 200711121015 cathy

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 local time:

touch -t 200711121015.30 drepper

Create or update a file called ; the resulting file has both the last data modification and last data access timestamps set to November 12, 2007 at 10:15:30 local time:

touch -t 0711121015.30 ebb9

Create or update a file called ; the resulting file has the last data access timestamp set to the corresponding time of the file named instead of the current time. If the file exists, the last data modification time is not changed:

touch -a -r mark eggert

The functionality of touch is described almost entirely through references to functions in the System Interfaces volume of POSIX.1-2008. In this way, there is no duplication of effort required for describing such side-effects as the relationship of user IDs to the user database, permissions, and so on.

There are some significant differences between the touch utility in this volume of POSIX.1-2008 and those in System V and BSD systems. They are upwards-compatible for historical applications from both implementations:

  1. In System V, an ambiguity exists when a pathname that is a decimal number leads the operands; it is treated as a time value. In BSD, no time value is allowed; files may only be touch ed to the current time. The -t time construct solves these problems for future conforming applications (note that the -t option is not historical practice).
  2. The inclusion of the century digits, CC, is also new. Note that a ten-digit time value is treated as if YY, and not CC, were specified. The caveat about the range of dates following the Epoch was included as recognition that some implementations are not able to represent dates beyond 18 January 2038 because they use signed int as a time holder.

The -r option was added because several comments requested this capability. This option was named -f in an early proposal, but was changed because the -f option is used in the BSD version of touch with a different meaning.

At least one historical implementation of touch incremented the exit code if -c was specified and the file did not exist. This volume of POSIX.1-2008 requires exit status zero if no errors occur.

In previous version of the standard, if at least two operands are specified, and the first operand is an eight or ten-digit decimal integer, the first operand was assumed to be a date_time operand. This usage was removed in this version of the standard since it had been marked obsolescent previously.

The -d date_time format is an ISO 8601:2000 standard complete representation of date and time extended format with an optional decimal point or <comma> followed by a string of digits following the seconds portion to specify fractions of a second. It is not necessary to recognize "[+/-]hh:mm" and "[+/-]hh" to specify timezones other than local time and UTC. The T time designator in the ISO 8601:2000 standard extended format may be replaced by <space>.

None.

date(1)

XBD V1_chap04(7), V1_chap08(7), V1_chap12(7), <sys/stat.h>

XSH creat(3), futimens(3), time(3), utime(3)

First released in Issue 2.

The obsolescent date_time operand is removed.

The Open Group Corrigendum U027/1 is applied. This extends the range of valid time past the Epoch to at least the time 0 hours, 0 minutes, 0 seconds, January 1, 2038, Coordinated Universal Time. This is a new requirement on POSIX implementations.

The range for seconds is changed from [00,61] to [00,60] to align with the ISO/IEC 9899:1999 (“ISO C99”) standard, and to allow for positive leap seconds.

Austin Group Interpretation 1003.1-2001 #118 is applied.

Austin Group Interpretation 1003.1-2001 #193 is applied, adding support for subsecond timestamps.

SD5-XCU-ERN-45 is applied, adding a new paragraph to the RATIONALE.

SD5-XCU-ERN-97 is applied, updating the SYNOPSIS.

SD5-XCU-ERN-110 is applied, updating the OPTIONS section.

Changes are made related to support for finegrained timestamps.

January 1, 2013 posix.fail